Tutorial Gloria blouse

Meet Gloria, the adorable little sister of our newest Phoebe blouse for women—the perfect excuse for another sweet twinning project! Let's start sewing this beauty!

Pin the top of the lower sleeve to the sleeve hem, right sides together and stitch. Finish the seam allowances together with an overlock or by zigzagging and press them towards the sleeve. 

If you’re adding piping, stitch it to the sleeve before adding on the lower sleeve. 

Gather the upper edge (the long, diagonal seam) of each front between the markings. Using the longest stitch on your sewing machine and without backstitching, sew one row of gathering stitches 1 cm from the edge and a second row 0,5 cm from the edge. Also, gather the section between the two markings at the center back. 

Pin a sleeve to each front, right sides together, and stitch the armhole seam. Finish the seam allowances together with an overlock or by zigzagging and press towards the front. 

Pin both sleeves to the back, right sides together. Stitch the armhole seams. Finish the seam allowances together with an overlock or by zigzagging and press them towards the back. 

Finish the shoulder seams of the front and back yokes with an overlock or by zigzagging. Pin the shoulder seams, right sides together, and stitch. Press the seams open. 

Would you like to add piping? Pin the piping all around the front and back yokes at the right side of the fabric. Start at the center front and align the raw edge of the piping with the raw edge of the fabric. Position the stitching line of the piping, where you will stitch along, at 1 cm from the edge. Pin or baste all around, then stitch directly beside the piping cord. Remove the basting stitches. 

Pin the front and back yokes to the blouse, right sides together. Start by matching the fronts to the front yokes. Align the basting marks precisely at the center front. Adjust the gathers so each front fi ts its front yoke neatly. Match the marking on the front yoke to the seam between the front and sleeve. At the back, distribute the gathers evenly across the center back so the back fi ts the yoke neatly. Stitch in place over the entire length. 

Finish the seams together with an overlock or by zigzagging and press towards the yokes. If you’re adding piping, stitch exactly in your previous stitching line.

Pin and stitch the side seams of the fronts and back and the seams of the sleeves, right sides together. Finish the seam allowances together with an overlock or by zigzagging and press them towards the front. 

Press the blouse hem 2 cm to the wrong side. Then press half of this allowance also to the wrong side. Stitch in place next to the edge. 

Press one of the long sides of the neck bias tape 1 cm to the wrong side. Pin the unpressed side of the bias tape to the neckline, right sides together and stitch in place. 

Grade the seam allowance of the neckline. Fold the bias tape around the seam allowance of the neckline and pin to the wrong side of the blouse. Stitch in place close to the edge. 

The button placket:

Fold the button placket in half lengthwise, wrong sides together, and press. Open it again and press one long edge 1 cm to the wrong side. 

Fold the button placket in half lengthwise again, right sides together. Pin the top and bottom edges and stitch. Make sure the folded seam allowance stays in place. Trim the corners on the top and bottom. Gently push out the corners and turn to the right side. Press. 

Pin the unpressed side of the button placket to the front, right sides together and stitch. 

Press the seam allowances to the inside of the button placket and fold the placket into place. Pin and stitch on the button placket close to the seam, from neckline to hem. Press neatly. 

The sleeve hem:

Press the sleeve hem 2,5 cm to the wrong side. Then press half of this seam allowance to the inside. Stitch close to the edge but leave a 2 cm opening. Use a small safety pin to pull the elastic through the casing. Stitch the elastic ends together and distribute the fabric evenly around the sleeve. Close the opening. 

The buttons: 

Make the buttonholes in the right button placket at the markings and open them carefully. You can find the distances between the buttons per size here:

92: 6,2 cm 

134: 7,7 cm 

98: 6,5 cm

140: 8,1 cm

104: 6,7 cm

146: 8,4 cm

110: 6,2 cm

152: 8,7 cm

116: 6,4 cm

158: 9,1 cm

122: 7 cm

164: 9,4 cm

128: 7,4 cm

Sew the buttons on the left button placket.

All done! We wish you a lot of fun twinning with Gloria and Phoebe! Show your creation on Facebook and Instagram with the hashtag #atelierjupeGloria or share it in our Facebook group ‘Atelier Jupe - Create & Share’. 


← Older Post